天然产物研究与开发 ›› 2012, Vol. 23 ›› Issue (09): 1279-.doi: A

• 开发研究 • 上一篇    下一篇

喷雾干燥制备高纯α-亚麻酸微胶囊研究

郭智军1,2,陈元涛1,2*,张炜1,2,杨威2,米林2,徐江波1,2,肖江1,2   

  1. 1青海师范大学化学系;2青海师范大学润德亚麻籽工程技术研究中心,西宁 810008
  • 出版日期:2012-09-29 发布日期:2013-01-06
  • 基金资助:

    青海省重点科技攻关项目(2007-N-120);科技部科技人员服务企业行动项目(2009GJG20017);教育部“新世纪优秀人才”支持计划(NCET-07-0476)。

Study on Spray-drying Microencapsulation of High-purity α-linolenic Acid

GUO Zhi-jun1, 2, CHEN Yuan-tao1,2*, Zhang Wei1,2, Yang Wei2, Mi Lin2, XU Jiang-bo1, 2, XIAO Jiang1,2   

  1. 1Department of Chemistry, Qinghai Normal University; 2Runde Engineering technology research Center of Flaxseed, Qinghai Normal University, Xining 810008, China
  • Online:2012-09-29 Published:2013-01-06

摘要: 本文采用喷雾干燥法制备高纯α-亚麻酸为芯材、亚麻籽胶为壁材的微胶囊,并以微胶囊化效率和含油率为指标,考察了制备工艺。结果表明,最佳微胶囊原料配方为:芯材与壁材的比例为(m/m)3:2,料液浓度为5%,进料温度为20 ℃;最佳喷雾干燥工艺条件:进风温度为180 ℃,出风温度为80 ℃,雾化器转速21000 r/min,进料速度为42.01 mL/min。在此工艺条件下亚麻油的微胶囊化效率为96.18%,含油率为60.09%。

关键词: 亚麻胶;&alpha, -亚麻酸;喷雾干燥

Abstract: The microencapsulation of high-purity α-linolenic acid was prepared with the spray drying method using high-purity α-linolenic acid as core material and flaxseed gum as wall material. The acting factors of preparing high-purity α-linolenic acid microcapsule have been investigated in detail according to microencapsulation efficiency and the ratio of oil content. The results showed that the best material compositions for microencapsulation were as follows: core material/wall material(m/m) 3:2, material concentration (mass-volume percentage, core material plus wall materials to mixed solution) 5%, and feeding temperature 20 ℃; the optimal spray drying processing conditions were determined as follows, the air temperature at the inlet was 180 ℃, while at the exit was 80 ℃, the rotating speed of centrifugal atomizer was 21000 r/min, and liquid feed rate was 42.01 mL/min. The content of microencapsulation efficiency was 96.18% and the ratio of oil content was 60.09%.

Key words: flaxseed gum, α-linolenic acid, spray drying

中图分类号: 

R 284.2